23/05/2011

I gave my presentation and got some feedback

for what I need to make sure I have done for the

final assessment on the 13th June. I had missed

some points out in my presentation so Kate told

me to make sure they're included in my sketchbook.

I need to use this feedback as a checklist to see

all is done.

In the afternoon I continued with completing my

model.

I continued with cutting of the remaining unwanted

parts and started filing down the sharpe ends.

I made sure everything that need to be stuck down

was done, and that the few bits that would be stuck

down after most the exhibition was stuck up were in

the right places.

20/05/2011 3D design

Using a spot welder I welded the pieces together making
sure that the pieces are joined in the correct places by
using a template.
It was difficult to hold the pieces and press the spot
welder at the same time, as the pieces kept moving out of
place, so I asked Zulfikar to help me and he pressed down
the spot welder.
Once that was done, I started to cut out the access pieces.
At time it got a little difficult to cut some pieces because
the positions, but by keeping the saw in a differet angle I
slowly managed to cut off the unwanted pieces.

3D Design 19/05/2011

For the window design I wanted to use cooper
wire. Matt told me that I could also use metal
rod, which is a little thick. But to use this I
had to make my design much simpler.


After choosing the lines I will keep, I started
to cut out each piece. The pieces were cut slightly
longer so that they can be spot welded in the correct
places.

3D Design 16/05/2011

I drilled the holes into the aluminium pieces so that
I could attach them to the MDF pieces.
Just before I was about to attach the parts together,
I released I hadn't painted the base or re-coated the
MDF pieces, so I did that.
After the paint dried I attached the aluminium and MDF
piece together with pop-rivets using the pop-rivet gun.
This took a while to do as it was a little hard. Because
my hand & arm started to hurt again, Kate helped me to
attach the pieces.
I softly hammerd down the pieces so that they would
properly sit in place.

3D Design 12/05/2011

Continuing with making my model, I drilled 11
holes into each MDF piece so that I can screw
the brackets into place.
Once the brackets were attached I glued the
MDF pieces into place, using PVA wood glue
and woodblocks to support.
I then hand bent the alaminium piece over a
rounded surface. I didn't use the roller because
when I tested it earlier on in the project, it left
marks and dents.
This prosess worked well and the pieces sat on
top of the model fine.

10/05/2011 3D design

During Visual Studies lesson I carried on with making
my model. I drilled the remaining pieces for the brackets
and filed down the rough parts. I finally then bent them
using the metal bender.
I made another set of brackets for the second MDF piece.

I started to paint my model with spray paint. I had to do
this outside, but because it was a little windy my pieces
kept getting a little dirty. I will have to re-paint them once
the spray piant has dried.




I stayed behind after college and made a small model
to test my new design using foam board. It seems that
it will work out well.


I developed my design further in CAD programme SketchUp
so I can visualise what it will look like.

3D Design 28/04/2011

Date/Time: 10/05, 10:04

In the lesson I started to produce my final

piece, which is a model of the my idea for

the arena/stadium.

After working out the measurements to

scale, I managed to cut out the main MDF

pieces required to build my model.

I wasn't able to do much more as the pain

in my hand/arm started again.

It wasn't a productive day. This dissappionted

me, as I wanted to get a lot of work done.

I must make sure I documentate my work in

my sketchbook and keep it up-to-date.